Difference between revisions of "Switch Mod Plates"
Line 5: | Line 5: | ||
<div class="whitebox"> | <div class="whitebox"> | ||
= Switch Mod Plates = | = Switch Mod Plates = | ||
− | + | [[File:DSC 7447 - 2000px.jpg|1000px|link=]] | |
− | |||
− | + | Switch tester plates tools used to organise switches for lubing and modding, known as 'lube stations' by other designers. | |
− | + | These units differ from the competition by being grippy, holding switches in place as you work on them. After you're done modding switches, simply close the top housing and push them out from below. | |
− | |||
− | |||
− | |||
− | |||
[[File:Switch Mod Plate Comparison 2000px.jpg|1000px|link=]] | [[File:Switch Mod Plate Comparison 2000px.jpg|1000px|link=]] | ||
Line 24: | Line 19: | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | == Specs == | |
+ | Sizes: 3x8, 4x10 | ||
+ | |||
+ | Material: 6mm matte frosted acrylic | ||
+ | |||
+ | Origin: Australia | ||
+ | |||
+ | |||
+ | == Features == | ||
+ | ===== Grippy slots ===== | ||
+ | Unlike other 'lube stations' on the market, my units have grippy slots which mean switches are held in place by the plate (like my tester units). | ||
+ | |||
+ | This can be a pro or a con depending on your workflow, but I personally prefer this as do many of my keyboard friends. | ||
+ | |||
+ | The main purpose of this is to allow you to rotate the plate around as you lube the bottom housing. Bumps will not cause switch parts to go flying off the plate. And lastly, the plate can be used as a switch tester - important if you want to check your work for consistency. | ||
+ | |||
+ | |||
+ | ===== Switch support ===== | ||
+ | Tester plates support any MX style switches such as cherry, kailh, kailh box, outemu, tecsee, durock etc. Some switches may sit a bit tighter or looser. Tester plates are a bit tighter than mod plates (which can be used as testers). | ||
− | + | ===== Material and finish ===== | |
+ | The acrylic is clear with a silky smooth satin/frosted texture on both sides, that resists dust and fingerprints. This is the same material used for my keyboard stands and other products. | ||
− | + | ===== Rubber feet ===== | |
− | + | Clear 3M rubber feet are pre-applied on each unit so it's ready to use after removing packaging. 4x6 units have an extra 2 bumpons in the center to maintain stability. | |
− | |||
+ | == Where to Buy == | ||
− | + | Switch Tester Plates are currently available from 3 aussie vendors. | |
− | + | ||
− | + | :• [https://www.switchkeys.com.au/collections/modification-accessories/products/laser-ninja-switch-tester-plate Switchkeys] | |
− | + | :• [https://customkbd.com/products/laser-ninja-switch-tester-plate Custom KBD] | |
+ | :• [https://mountainkeyboards.com/products/laser-ninja-switch-tester-plate Mountain Keyboards] | ||
− | |||
− | |||
− | + | Direct purchase is also possible by messaging me on discord. If you are international, I recommend checking out the vendors above as they'll have better rates. | |
+ | Discord: @Ninja#5071 | ||
[[File:ProfilePic Discord.jpg|link=]] | [[File:ProfilePic Discord.jpg|link=]] | ||
</div> | </div> |
Revision as of 03:00, 14 June 2022
Contents
Switch Mod Plates
Switch tester plates tools used to organise switches for lubing and modding, known as 'lube stations' by other designers.
These units differ from the competition by being grippy, holding switches in place as you work on them. After you're done modding switches, simply close the top housing and push them out from below.
Specs
Sizes: 3x8, 4x10
Material: 6mm matte frosted acrylic
Origin: Australia
Features
Grippy slots
Unlike other 'lube stations' on the market, my units have grippy slots which mean switches are held in place by the plate (like my tester units).
This can be a pro or a con depending on your workflow, but I personally prefer this as do many of my keyboard friends.
The main purpose of this is to allow you to rotate the plate around as you lube the bottom housing. Bumps will not cause switch parts to go flying off the plate. And lastly, the plate can be used as a switch tester - important if you want to check your work for consistency.
Switch support
Tester plates support any MX style switches such as cherry, kailh, kailh box, outemu, tecsee, durock etc. Some switches may sit a bit tighter or looser. Tester plates are a bit tighter than mod plates (which can be used as testers).
Material and finish
The acrylic is clear with a silky smooth satin/frosted texture on both sides, that resists dust and fingerprints. This is the same material used for my keyboard stands and other products.
Rubber feet
Clear 3M rubber feet are pre-applied on each unit so it's ready to use after removing packaging. 4x6 units have an extra 2 bumpons in the center to maintain stability.
Where to Buy
Switch Tester Plates are currently available from 3 aussie vendors.
Direct purchase is also possible by messaging me on discord. If you are international, I recommend checking out the vendors above as they'll have better rates.
Discord: @Ninja#5071